1991 Chevy C 1500 P/U Ignition Control Module: Service and Repair
download REMOVAL: 1. 2. 3. 4. Remove distributor cap and rotor. Remove two module attaching screws, and lift module up. Disconnect leads from module. Observe color code on leads as these cannot be...
View Article2001 Chevy S10/T10 Blazer Distributor Replacement REMOVAL PROCEDURE
download NOTE: There are two procedures available to install the distributor. Use Installation Procedure 1 when the crankshaft has NOT been rotated from the original position. Use Installation...
View Article1994-1998 Mazda Trucks Repair Guide Crankshaft Damper REMOVAL & INSTALLATION
download REMOVAL & INSTALLATION See Figures 1, 2, 3, 4 and 5 1. Disconnect the negative battery cable. 2. Remove the engine fan/clutch assembly and shroud. 3. Remove the accessory drive belt(s). 4....
View Article2003 Chrysler PT Cruiser OIL PUMP REMOVAL
download 1. 2. 3. 4. Disconnect negative cable from battery. Remove timing belt. Remove timing belt rear cover. Remove oil pan. 5. Remove crankshaft sprocket using Special Tools 6793 and C-4685-C2...
View Article1984 Jeep CJ7 MOTORCRAFT SOLID STATE IGNITION (SSI) TESTING
download SECONDARY CIRCUIT CHECK CAUTION: When checking secondary voltage, do not remove spark plug wires from spark plugs No. 3 on 4-cylinder, No. 1 or 5 on 6-cylinder and No. 3 or 4 on V8 Engines. 1....
View Article2000 Ford F-Super Duty 250-550 Hub Removal
download 1. Set the parking brake. 2. Loosen the retaining bolts. 3. Raise the vehicle to the desired working height, keeping the axle parallel with the floor; for additional information, refer to...
View Article1999 Honda Civic LX Distributor REMOVAL & INSTALLATION
download Fig. Exploded view of a Hitachi style distributor Fig. Exploded view of a TEC style distributor Fig. Distributor mounting bolt torque Fig. Position of the ignition wires on the distributor cap...
View Article2003 Ford Focus ZTW HUB/ STEERING KNUCKLE ASSEMBLY Removal
download 1. Loosen the strut tower nuts by at least five turns. See Fig. 4 . Loosen the wheel hub retaining nut. Raise and support vehicle. Remove front wheel, brake caliper and rotor. Remove ABS wheel...
View Article1997 Ford Aerostar/Ranger Wheel Grease Seal and Bearing Front Replacement and...
download The recommended wheel bearing lubricant is lithium-base High-Temperature Constant Velocity Joint Grease E43Z-19590-A or equivalent meeting Ford specification ESP-M1C207-A. CAUTION: Sodium-base...
View ArticleRenault CLIO II with AC: XBXX – K9K – K4J – K4M engines Alternator pulley...
download Special tooling required Mot. 1732 Tool for removing and re?tting the alternator pulley Tightening torquesm the alternator decou- pling pulley I – PARTS AND CONSUMABLES FOR THE REPAIRS Parts...
View ArticleENGINE PERFORMANCE 1993 Suzuki Swift
1993 ENGINE PERFORMANCE Suzuki of America Corp. On-Vehicle Adjustments Suzuki; Samurai, Sidekick, Swift ENGINE MECHANICAL Before performing any on-vehicle adjustments to fuel or ignition system, ensure...
View Article2002 Mazda Protege LX TIMING BELT Removal
download 1. Disconnect negative battery cable. Remove Crankshaft Position (CKP) and Camshaft Position (CMP) sensors from front of engine (if equipped). See Fig. 1 . Remove spark plugs. 2. Remove...
View Article1997 Aerostar/ Ranger Wheel Grease Seal and Bearing, Front Replacement and...
download Automatic Locking Hub, Exploded View, Ranger Wheel Hub Grease Seal 2 4222 Wheel Bearing Cup 3 1102 Rotor 4 1197 Inner Locknut 5 3B549 Washer 6 3B548 Axle Shaft Spacer 7 3B396 Hub 8 1A107...
View Article1993 Ford Explorer SPINDLE Removal
download 1. Raise and support front of vehicle. Remove wheel and tire assembly. Remove brake caliper from rotor and wire it to under-body to prevent damage to brake hose. 2. Remove dust cap, cotter...
View Article2007 – 2010 Camry Brake Vibration
download Repair Procedure 1. Machine both front rotors with an on-car lathe to minimize rotor run-out. Make sure that the rotors are within minimum thickness. After machining, the maximum allowed rotor...
View Article
More Pages to Explore .....